×
Controller Supply-HM-V1-T
Controller Supply-HM-V1-T
  • RF remote, 0/1-10V, Push Dim (3-in-1) hämardamine.
  • 4096 levels 0-100% dimming smoothly without any flflash.
  • Match with RF 2.4G single zone or multiple zone dimming remote control.
  • One RF controller accept up to 10 remote control.
  • Auto-transmitting function: Controller automatically transmit signal to another controller with 15m control distance.
  • Synchronize on multiple number of controllers.
  • Connect with external push switch to achieve on/off and 0-100% dimming function.
  • Light on/off fade time 3s selectable.
  • Over-heat / Over-load / Short circuit protection, recover automatically
Toote detail Tagasiside kohe

 

 

 

Inpuf and Oufput
Input voliage 12-24VDC
Input current 20.5A
Output voltage 12-24VDC
Output current 1CH,20A
Output power 240W/480W

(12V/24V)

Ouput ype Constant volage

 

Dimming data
Input signal RF 2.4GHz

0/1-10V

Push Dim

Control distance 15m(Barrier-free space)
Dimming gray scale 4096(2^12)levels
Dimming range 0 -100%
Dimming curve Logarithmic
PWM Frequency 500Hz(default)

 

 

Ohutus ja EMC
EMC standard (EMC) OTSI EE 301 489-1 V2.2.3

OTSI EE 301 489-17 V3.2.4

Safety standard(LVD EN 62368-1:2020+A11:2020
Radio Equipment(PUNANE) OTSI EE 300 328 V2.2.2
Certification SEE,EMC,LVD,PUNANE

 

 

Keskkond
Operation temperature Vastamisi: -30°C ~ +55°C
Case temperature (Max.) T c:+85°C
IP reiting IP20

 

 

Warranty and Protection
Garantii 5 aastat
Protection Reverse polarity

Over-heat

Over-load

Short circuit

 

 

Weight
Net weight 0.234kg
Gross weight 0.054kg

 

 

 

 

 

Mechanical Structures and Installations

 

 

 

Wiring Diagram

 

 

 

 

 

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

 

 

Match Remote Control (two match ways)

 

End user can choose the suitable match/delete ways. Two options are offered for selection:

 

Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

 

0/1-10V Dimming

  • The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.
  • Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
  • We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 meetrit.
  • If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

 

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

  • Short press:

Turn on or off light.

  • Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

  • Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

  • Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 meetrit.

 

Dimming Curve

 

 

 

Light on/off fade time

 

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

 

 

Malfunctions Analysis & Troubleshooting

 

Malfunctions Causes Troubleshooting
No light 1. No power.

2.Wrong connection or insecure.

1.Check the power.

2.Check the connection.

Uneven intensity between front and rear,with voltage drop 1. Output cable is too long.

2. Wire diameter is too small.

3.Overload beyond power supply capability.

4.Overload beyond controller capability.

1.Reduce cable or loop supply.

2.Change wider wire.

3.Replace higher power supply.

4.Add power repeater.

No response from the remote 1.The battery has no power.

2. Beyond controllable distance.

3.The controller did not match the remote.

1. Replace battery.

2.Reduce remote distance.

3. Re-match the remote.

 

 

Controller Supply-HM-V1-T-

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

Q1.l see on okei OEM ja ODM ?

Soomusvalgustus on professionaalne OEM- ja ODM-tellimuste jaoks. Meil on rikkalik kogemus tootmise jätkamiseks ja hea kvaliteedi tagamiseks.

 

Q2. Mis on MOQ? Kas ma saaksin mõned näidised ?

Madal MOQ, 1 tk proovide kvaliteedi kontrollimiseks on saadaval Proovide tellimus on vastuvõetav ja tere tulemast teie projekti jaoks kohandatud näidised.

 

Q3. Kui pikk tarneaeg?

Näidisvajadused 3-5 ARMOR võib muuta teie disaini üha autentsemaks ja väärtuslikumaks, koguse tellimus vajab 10-15 päeva

 

Q4.Kuidas te kaupa saadate ja kui kaua selle kohalejõudmine aega võtab?

Tavaliselt saadame DHL-iga, UPS, FedEx või TNT. Tavaliselt kulub 3-5 päevad kohale jõudmiseks. Lennu- ja meretransport on samuti valikuline.

 

Q5.Kuidas jätkata kohandatud valguse tellimist ?

Esiteks, andke meile teada oma nõuded või joonis.Teiseks, tsiteerime vastavalt teie nõuetele. Kolmandaks, kinnitate ja korraldate makse ametliku tellimuse eest. Lõpuks, alustame tootmist ja korraldame saadetise.

 

Q6.Kui kaua garantii kehtib?

Kõik Armouri valgustustooted on kvaliteetsed 3 aastat, lf kohandatud projektitooted 5-aastase garantiiga.

 

Q7. Kas tootele logo printimine on õige ?

Jah, palun teavitage meid enne tootmist ametlikult ja kinnitage kujundus esmalt meie proovi põhjal.

 

Q8. Kuidas vigadega toime tulla?

Meie pakume 2, 3 ja 5 aastane piiratud garantii erinevat tüüpi toodetele või erinevatele valgustusprojektide nõuetele. Selle aja jooksul, kui klientidel on kvaliteediprobleeme ja see tõend on soomusvalgustuse inseneride poolt heaks kiidetud, soovime defektsed asendada uute kvalifitseeritud esemetega.

Pange tähele, et garantii ei võrdu elueaga. Meie toodete eluiga on üle 50 000 tunni.

 

Q9. Kas ma saan teie tehast külastada?

Muidugi,tere tulemast meie tehast külastama. Can annab meile teie külastuse ajakava enne kahte päeva teada ja teie huvitatud toodetest.

 

Q10. Kas olete tehas või kaubandusettevõte?

Ekspordime tehasest otse üle mereturule.

 

Q11. Kas tarnite LED-valgustust mõnele kuulsale kaubamärgipoele Lighting?

Jah,meie led-pood Lighting varustas LANCOME-ga , LEGO,JÄRGMINE,TREENER, Burt's Bee,Hasbro, Saapad,BRAUN,M&S jne.

 

 

 

Saada meile oma sõnum:
UURI KOHE
UURI KOHE