Controller Supply-HM-V1-T

Controller Supply-HM-V1-T

RF remote, 0/1-10ວ, Push Dim (3-in-1) ມືດມົວ.
4096 levels 0-100% dimming smoothly without any flflash.
Match with RF 2.4G single zone or multiple zone dimming remote control.

One RF controller accept up to 10 remote control.
Auto-transmitting function: Controller automatically transmit signal to another controller with 15m control distance.

Synchronize on multiple number of controllers.
Connect with external push switch to achieve on/off and 0-100% dimming function.

Light on/off fade time 3s selectable.
Over-heat / Over-load / Short circuit protection, recover automatically

ສົ່ງອີເມວຫາພວກເຮົາ ຕິດຕໍ່ຕອນນີ້ Download as PDF

ລາຍລະອຽດຜະລິດຕະພັນ ຄຳຕິຊົມດຽວນີ້

Inpuf and Oufput
Input voliage	12-24VDC
Input current	20.5A
Output voltage	12-24VDC
Output current	1CH,20A
Output power	240W/480W (12V/24V)
Ouput ype	Constant volage

Dimming data
Input signal	RF 2.4GHz 0/1-10ວ Push Dim
Control distance	15m(Barrier-free space)
Dimming gray scale	4096(2^12)levels
Dimming range	0 -100%
Dimming curve	Logarithmic
PWM Frequency	500Hz(default)

Safety and EMC
EMC standard (EMC)	ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD	EN 62368-1:2020+A11:2020
Radio Equipment(RED)	ETSI EN 300 328 V2.2.2
Certification	CE,EMC,LVD,RED

Environment
Operation temperature	Ta: -30°C ~ +55°C
Case temperature (Max.)	T c:+85°C
IP rating	IP20

Warranty and Protection

ຮັບປະກັນ

5 ປີ

Protection

Reverse polarity

Over-heat

Over-load

Short circuit

Weight
Net weight	0.234kg
Gross weight	0.054kg

Mechanical Structures and Installations

Wiring Diagram

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

0/1-10V Dimming

The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.

Compliant with 0-10V, 1-10ວ, 10V PWM, RX(4 in 1).
We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.

If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

Short press:

Turn on or off light.

Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 meters.

Dimming Curve

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Malfunctions Analysis & Troubleshooting

Malfunctions	Causes	Troubleshooting
No light	1. No power. 2.Wrong connection or insecure.	1.Check the power. 2.Check the connection.
Uneven intensity between front and rear,with voltage drop	1. Output cable is too long. 2. Wire diameter is too small. 3.Overload beyond power supply capability. 4.Overload beyond controller capability.	1.Reduce cable or loop supply. 2.Change wider wire. 3.Replace higher power supply. 4.Add power repeater.
No response from the remote	1.The battery has no power. 2. Beyond controllable distance. 3.The controller did not match the remote.	1. Replace battery. 2.Reduce remote distance. 3. Re-match the remote.

Controller Supply-HM-V1-T-

Q1.ls ມັນບໍ່ເປັນຫຍັງສໍາລັບ OEM ແລະ ODM ?

ແສງສະຫວ່າງປະຈໍາຕະກູນແມ່ນເປັນມືອາຊີບສໍາລັບການສັ່ງຊື້ OEM ແລະ ODM. ພວກເຮົາມີປະສົບການອຸດົມສົມບູນ toproceed ການຜະລິດແລະຮັບປະກັນຄຸນນະພາບທີ່ດີ.

Q2.ແມ່ນຫຍັງ MOQ? ຂ້ອຍສາມາດມີຕົວຢ່າງບາງຢ່າງໄດ້ ?

MOQ ຕໍ່າ, 1 pcs ສໍາລັບຕົວຢ່າງການກວດສອບຄຸນນະພາບແມ່ນມີຄໍາສັ່ງຕົວຢ່າງແມ່ນຍອມຮັບແລະຍິນດີຕ້ອນຮັບຕົວຢ່າງທີ່ກໍາຫນົດເອງສໍາລັບໂຄງການຂອງທ່ານ.

Q3.How long of the Lead time?

ຄວາມຕ້ອງການຕົວຢ່າງ 3-5 ມື້, ຈໍານວນຄໍາສັ່ງຕ້ອງການ 10-15 ມື້

Q4.How ເຈົ້າສົ່ງສິນຄ້າແນວໃດແລະມັນໃຊ້ເວລາດົນປານໃດທີ່ຈະມາຮອດ?

ປົກກະຕິແລ້ວພວກເຮົາຈັດສົ່ງໂດຍ DHL, UPS, FedEx ຫຼື TNT. ມັນມັກຈະໃຊ້ເວລາ 3-5 ມື້ທີ່ຈະມາຮອດ. ສາຍການບິນແລະການຂົນສົ່ງທາງທະເລຍັງມີທາງເລືອກ.

Q5.How ເພື່ອດໍາເນີນການຄໍາສັ່ງສໍາລັບແສງສະຫວ່າງທີ່ກໍາຫນົດເອງ ?

ທໍາອິດ, ໃຫ້ພວກເຮົາຮູ້ຄວາມຕ້ອງການຂອງທ່ານຫຼືການແຕ້ມຮູບ.ທີສອງ, ພວກເຮົາອ້າງອີງຕາມຄວາມຕ້ອງການຂອງທ່ານ. ອັນທີສາມ, ທ່ານຢືນຢັນແລະຈັດການຈ່າຍເງິນສໍາລັບຄໍາສັ່ງຢ່າງເປັນທາງການ.ສຸດທ້າຍ, ພວກເຮົາຈະເລີ່ມຕົ້ນການຜະລິດແລະຈັດການຂົນສົ່ງ.

Q6.How ດົນປານໃດສໍາລັບການຮັບປະກັນ?

ທັງຫມົດຂອງຜະລິດຕະພັນເຮັດໃຫ້ມີແສງ Armor ຄຸນນະພາບແມ່ນ 3 ປີ, lf ຜະລິດຕະພັນໂຄງການທີ່ກໍາຫນົດເອງທີ່ມີການຮັບປະກັນ 5 ປີ.

Q7.ls ມັນດີທີ່ຈະພິມ LoGo ຂອງຂ້ອຍຢູ່ໃນຜະລິດຕະພັນ ?

ແມ່ນແລ້ວ, ກະລຸນາແຈ້ງພວກເຮົາຢ່າງເປັນທາງການກ່ອນທີ່ຈະຜະລິດແລະຢືນຢັນການອອກແບບທໍາອິດໂດຍອີງໃສ່ຕົວຢ່າງຂອງພວກເຮົາ.

Q8.How to deal with the Faulty?

ພວກເຮົາສະເຫນີ 2, 3 ແລະ 5 ການຮັບປະກັນຈໍາກັດຂອງປີສໍາລັບປະເພດຕ່າງໆຂອງຜະລິດຕະພັນຫຼືຄວາມຕ້ອງການທີ່ແຕກຕ່າງກັນຂອງໂຄງການເຮັດໃຫ້ມີແສງ. ໃນໄລຍະນີ້, ຖ້າລູກຄ້າມີບັນຫາຄຸນນະພາບຫຼັກຖານສະແດງແລະຫຼັກຖານນັ້ນຖືກອະນຸມັດໂດຍວິສະວະກອນເຮັດໃຫ້ມີແສງປະຈໍາຕະກູນ, ພວກເຮົາຢາກຈະທົດແທນສິ່ງທີ່ມີຂໍ້ບົກພ່ອງດ້ວຍລາຍການທີ່ມີຄຸນນະພາບໃຫມ່.

ກະລຸນາສັງເກດວ່າການຮັບປະກັນບໍ່ເທົ່າກັບ lifespan. ຜະລິດຕະພັນຂອງພວກເຮົາມີຫຼາຍກ່ວາ 50000-hourlong lifespan.

Q9.Can ຂ້າພະເຈົ້າໄປຢ້ຽມຢາມໂຮງງານຜະລິດຂອງທ່ານ?

ແນ່ນອນ,ຍິນດີຕ້ອນຮັບໄປຢ້ຽມຢາມໂຮງງານຂອງພວກເຮົາ. ສາມາດໃຫ້ພວກເຮົາຮູ້ຕາຕະລາງການຢ້ຽມຢາມຂອງທ່ານກ່ອນສອງມື້ແລະຜະລິດຕະພັນທີ່ສົນໃຈຂອງທ່ານ.

Q10.Are ທ່ານໂຮງງານຜະລິດຫຼືບໍລິສັດການຄ້າ?

ພວກເຮົາແມ່ນໂຮງງານຜະລິດໂດຍກົງສົ່ງອອກໄປຕະຫຼາດທະເລ.

Q11.Do ທ່ານສະຫນອງແສງສະຫວ່າງນໍາກັບຮ້ານຂາຍຖ່ານກ້ອນທີ່ມີຊື່ສຽງໃດໆ Lighting?

ແມ່ນແລ້ວ,ຮ້ານນໍາພາຂອງພວກເຮົາເຮັດໃຫ້ມີແສງສະຫນອງໃຫ້ແກ່ LANCOME , LEGO,ຕໍ່ໄປ,ຄູຝຶກສອນ, ເຜິ້ງ Burt,Hasbro, ເກີບ，BRAUN,ມ&S ແລະອື່ນໆ.