×
Controller Supply-HM-V1-T
Controller Supply-HM-V1-T
  • RF remote, 0/1-10V, Push Dim (3-in-1) LTECH barošanas avots.
  • 4096 levels 0-100% dimming smoothly without any flflash.
  • Match with RF 2.4G single zone or multiple zone dimming remote control.
  • One RF controller accept up to 10 remote control.
  • Auto-transmitting function: Controller automatically transmit signal to another controller with 15m control distance.
  • Synchronize on multiple number of controllers.
  • Connect with external push switch to achieve on/off and 0-100% dimming function.
  • Light on/off fade time 3s selectable.
  • Over-heat / Over-load / Short circuit protection, recover automatically
Informācija par produktu Atsauksmes tagad

 

 

 

Inpuf and Oufput
Input voliage 12-24VDC
Input current 20.5A
Output voltage 12-24VDC
Output current 1CH,20A
Output power 240W/480W

(12V/24V)

Ouput ype Constant volage

 

Dimming data
Input signal RF 2.4GHz

0/1-10V

Push Dim

Control distance 15m(Barrier-free space)
Dimming gray scale 4096(2^12)levels
Dimming range 0 -100%
Dimming curve Logarithmic
PWM Frequency 500Hz(default)

 

 

Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4

Safety standard(LVD EN 62368-1:2020+A11:2020
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Sertifikācija ŠO,EMC,LVD,RED

 

 

Environment
Operation temperature Sejas: -30°C ~ +55°C
Case temperature (Max.) T c:+85°C
IP vērtējums IP20

 

 

Warranty and Protection
Garantija 5 gadiem
Protection Reverse polarity

Over-heat

Over-load

Short circuit

 

 

Weight
Net weight 0.234kg
Gross weight 0.054kg

 

 

 

 

 

Mechanical Structures and Installations

 

 

 

Wiring Diagram

 

 

 

 

 

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

 

 

Match Remote Control (two match ways)

 

End user can choose the suitable match/delete ways. Two options are offered for selection:

 

Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

 

0/1-10V Dimming

  • The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.
  • Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
  • We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
  • If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

 

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

  • Short press:

Turn on or off light.

  • Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

  • Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

  • Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 meters.

 

Dimming Curve

 

 

 

Light on/off fade time

 

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

 

 

Malfunctions Analysis & Troubleshooting

 

Malfunctions Causes Troubleshooting
No light 1. No power.

2.Wrong connection or insecure.

1.Check the power.

2.Check the connection.

Uneven intensity between front and rear,with voltage drop 1. Output cable is too long.

2. Wire diameter is too small.

3.Overload beyond power supply capability.

4.Overload beyond controller capability.

1.Reduce cable or loop supply.

2.Change wider wire.

3.Replace higher power supply.

4.Add power repeater.

No response from the remote 1.The battery has no power.

2. Beyond controllable distance.

3.The controller did not match the remote.

1. Replace battery.

2.Reduce remote distance.

3. Re-match the remote.

 

 

Controller Supply-HM-V1-T-

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

Q1.l Tas ir labi OEM un ODM ?

Bruņu apgaismojums ir profesionāls OEM un ODM pasūtījumiem. Mums ir bagāta pieredze, lai turpinātu ražošanu un nodrošinātu labu kvalitāti.

 

Q2. Kāds ir MOQ? Vai es varu saņemt dažus paraugus ?

Zems MOQ, 1 ir pieejami parauga kvalitātes pārbaudei paredzētie gab. Paraugu pasūtījums ir pieņemams, un laipni lūdzam jūsu projektam pielāgotos paraugus.

 

Q3. Cik ilgs izpildes laiks?

Parauga vajadzības 3-5 dienas, daudzuma pasūtījumam nepieciešamas 10-15 dienas

 

Q4. Kā jūs nosūtāt preces un cik ilgs laiks nepieciešams, lai tās saņemtu?

Mēs parasti piegādājam ar DHL, UPS, FedEx vai TNT. Tas parasti prasa 3-5 dienas līdz ierašanās brīdim. Aviopārvadājumi un jūras pārvadājumi arī nav obligāti.

 

Q5. Kā veikt pielāgotas gaismas pasūtījumu ?

Pirmkārt, paziņojiet mums par savām prasībām vai zīmējumu. Otrkārt, mēs citējam saskaņā ar jūsu prasībām. Treškārt, jūs apstiprināt un organizēt maksājumu par oficiālu pasūtījumu. Beidzot, mēs sāksim ražošanu un organizēsim sūtījumu.

 

Q6. Cik ilgi ir garantija?

Visu Armor apgaismojuma produktu kvalitāte ir 3 gadiem, lf pielāgotiem projekta produktiem ar 5 gadu garantiju.

 

7. jautājums ir pareizi uz izstrādājuma uzdrukāt savu logotipu ?

Jā, lūdzu, oficiāli informējiet mūs pirms ražošanas un vispirms apstipriniet dizainu, pamatojoties uz mūsu paraugu.

 

Q8. Kā rīkoties ar bojāto?

Mēs piedāvājam 2, 3 un 5 gada ierobežotā garantija dažāda veida produktiem vai dažādām apgaismojuma projektu prasībām. Šajā periodā, ja klientiem ir kvalitātes problēmas un šo pierādījumu ir apstiprinājuši bruņu apgaismojuma inženieri, mēs vēlētos nomainīt bojātās preces ar jaunām kvalificētām precēm.

Lūdzu, ņemiet vērā, ka garantija nav vienāda ar kalpošanas laiku. Mūsu produktu kalpošanas laiks pārsniedz 50 000 stundu..

 

Q9. Vai es varu apmeklēt jūsu rūpnīcu?

Protams,laipni lūdzam apmeklēt mūsu rūpnīcu. Var informēt mūs par jūsu apmeklējumu grafiku pirms divām dienām un jūsu ieinteresētajiem produktiem.

 

Q10. Vai jūs esat rūpnīca vai tirdzniecības uzņēmums?

Mēs rūpnīcā tieši eksportējam uz jūras tirgu.

 

Q11. Vai jūs piegādājat LED apgaismojumu kādam slavenu zīmolu veikalam Lighting?

Jā,mūsu vadītajam veikalam Lighting bija piegāde LANCOME , LEGO,TĀLĀK,TRENERIS, Bērta bite,Hasbro, Zābaki,BRAUN,M&S utt.

 

 

 

Nosūtiet mums savu ziņojumu:
IZMEKLĒJIET TAGAD
IZMEKLĒJIET TAGAD