×
Controller Supply-HM-V1-T
Controller Supply-HM-V1-T
  • RF remote, 0/1-10වී, Push Dim (3-in-1) අඳුරු වීම.
  • 4096 levels 0-100% dimming smoothly without any flflash.
  • Match with RF 2.4G single zone or multiple zone dimming remote control.
  • One RF controller accept up to 10 remote control.
  • Auto-transmitting function: Controller automatically transmit signal to another controller with 15m control distance.
  • Synchronize on multiple number of controllers.
  • Connect with external push switch to achieve on/off and 0-100% dimming function.
  • Light on/off fade time 3s selectable.
  • Over-heat / Over-load / Short circuit protection, recover automatically
දැන් අමතන්න PDF ලෙස බාගන්න
නිෂ්පාදන විස්තර දැන් ප්‍රතිපෝෂණය

 

 

 

Inpuf and Oufput
Input voliage 12-24VDC
Input current 20.5A
Output voltage 12-24VDC
Output current 1CH,20A
Output power 240W/480W

(12V/24V)
Ouput ype Constant volage

 

Dimming data
Input signal RF 2.4GHz

0/1-10වී

Push Dim
Control distance 15m(Barrier-free space)
Dimming gray scale 4096(2^12)levels
Dimming range 0 -100%
Dimming curve Logarithmic
PWM Frequency 500Hz(default)

 

 

Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4
Safety standard(LVD EN 62368-1:2020+A11:2020
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certification CE,EMC,LVD,RED

 

 

Environment
Operation temperature Ta: -30°C ~ +55°C
Case temperature (Max.) T c:+85°C
IP rating IP20

 

 

Warranty and Protection
Warranty 5 අවුරුදු
Protection Reverse polarity

Over-heat

Over-load

Short circuit

 

 

Weight
Net weight 0.234kg
Gross weight 0.054kg

 

 

 

 

 

Mechanical Structures and Installations

 

 

 

Wiring Diagram

 

 

 

 

 

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

 

 

Match Remote Control (two match ways)

 
End user can choose the suitable match/delete ways. Two options are offered for selection:

 
Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

 Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

 

0/1-10V Dimming

  • The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.
  • Compliant with 0-10V, 1-10වී, 10V PWM, RX(4 තුල 1).
  • We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
  • If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

 

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

  • Short press:

Turn on or off light.

  • Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

  • Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

  • Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 meters.

 

Dimming Curve

 

 

 

Light on/off fade time

 

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

 

 

Malfunctions Analysis & Troubleshooting

 

Malfunctions Causes Troubleshooting
No light 1. No power.

2.Wrong connection or insecure.

 1.Check the power.

2.Check the connection.
Uneven intensity between front and rear,with voltage drop 1. Output cable is too long.

2. Wire diameter is too small.

3.Overload beyond power supply capability.

4.Overload beyond controller capability.

 1.Reduce cable or loop supply.

2.Change wider wire.

3.Replace higher power supply.

4.Add power repeater.
No response from the remote 1.The battery has no power.

2. Beyond controllable distance.

3.The controller did not match the remote.

 1. Replace battery.

2.Reduce remote distance.

3. Re-match the remote.

 

 

Controller Supply-HM-V1-T-

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

 

Controller Supply-HM-V1-T-

Q1.ls it okay for OEM and ODM ?

OEM සහ ODM ඇණවුම සඳහා ආමර් ආලෝකකරණය වෘත්තීය වේ. We have rich experience toproceed the production and ensure the good quality.

 

Q2.What's the MOQ? Can l have some samples ?

අඩු MOQ, 1 pcs for sample checking quality is available Samples order are acceptableand welcome the customized samples for your project.

 

Q3.How long of the Lead time?

නියැදි අවශ්‍යතා 3-5 දින, ප්‍රමාණ අනුපිළිවෙලට දින 10-15 ක් අවශ්‍යයි

 

Q4.How do you ship the goods and how long does it take to arrive?

අපි සාමාන්‍යයෙන් නැව්ගත කරන්නේ ඩීඑච්එල්, UPS, ෆෙඩෙක්ස් හෝ ටීඑන්ටී. lt usually takes 3-5 days to arrive.Airlineand sea shipping also optional.

 

Q5.How to proceed an order for customized light ?

පළමුවන, ඔබගේ අවශ්‍යතා හෝ චිත්‍ර ඇඳීම අපට දන්වන්න. දෙවනුව, we quote according to yourrequirements.Third, විධිමත් ඇණවුමක් සඳහා ගෙවීම් ඔබ විසින් තහවුරු කර ඇත, we willstart the production and arrange shipment.

 

Q6.How long for the warranty?

සියලුම ආමර් ආලෝකකරණ නිෂ්පාදනවල ගුණාත්මකභාවය 3 අවුරුදු, lf customized project products with 5years warranty.

 

Q7.ls it okay to print my LoGo on the product ?

ඔව්, please inform us formally before production and confirm the design firstly basedon our sample.

 

Q8.How to deal with the Faulty?

අපි පිරිනමමු 2, 3 සහ 5 year's limited warranty for different kinds of products or differentrequirements of lighting projects. මෙම කාලය තුළ, if customers have the proofshowing quality issues and that proof is approved by armor lighting engineers, we wouldlike to replace the defective ones with new qualified items.

Please note that warranty is not equal to lifespan.Our products have more than 50000-hourlong lifespan.

 

Q9.Can l visit your factory?

ෂුවර්,අපගේ කර්මාන්ත ශාලාව නැරඹීමට සාදරයෙන් පිළිගනිමු. Can lets us know your visit schedule before two daysand your interested products.

 

Q10. ඔබ කර්මාන්ත ශාලාවක් හෝ වෙළඳ සමාගමක්ද??

අපි කර්මාන්තශාලා සෘජුවම මුහුදු වෙළඳපොළට අපනයනය කරනවා.

 

Q11. ඔබ ඕනෑම ප්‍රසිද්ධ වෙළඳ නාම වෙළඳසැලකට ආලෝකකරණය සපයන්නේද??

ඔව්,අපගේ ප්‍රමුඛ වෙළඳසැල ලයිටින් ලැන්කොම් වෙත සැපයුමක් තිබුණි , ලෙගෝ,ඊළඟ,පුහුණුකරුවා, Burt's Bee,හස්බ්‍රෝ, බූට්ස්，බ්‍රවුන්,එම්&එස් යනාදිය.

 

 

 

ටැග්：, ,
ඔබේ පණිවිඩය අපට එවන්න:
දැන් විමසන්න

නිෂ්පාදන නිර්දේශය

දැන් විමසන්න